Tay Điều Khiển Radiomaster T8 Lite M2 | Chính hãng
Tay Điều Khiển Radiomaster T8 Lite M2 | Chính hãng
Tay Điều Khiển Radiomaster T8 Lite M2 | Chính hãng
Tay Điều Khiển Radiomaster T8 Lite M2 | Chính hãng
Tay Điều Khiển Radiomaster T8 Lite M2 | Chính hãng
Tay Điều Khiển Radiomaster T8 Lite M2 | Chính hãng
Tay Điều Khiển Radiomaster T8 Lite M2 | Chính hãng
1 / 1

Tay Điều Khiển Radiomaster T8 Lite M2 | Chính hãng

0.0
0 đánh giá

RadioMaster T8 Lite V2 2.4GHz 8CH CC2500 D8 D16 V1 Protocol Potentiometer Sensor Gimbal USB-C Charging Radio Transmitter for RC Drone Description: (Manual) Brand Name: RadioMaster Item Name: T8 Lite V2 Transmitter Model: T8 Lite V2 Mode: Mode1/Mode2 Size: 160*130*45mm

1.199.000
Share:
4.9/5

Đánh giá

1.221

Theo Dõi

1.012

Nhận xét

RadioMaster T8 Lite V2 2.4GHz 8CH CC2500 D8 D16 V1 Protocol Potentiometer Sensor Gimbal USB-C Charging Radio Transmitter for RC Drone Description: (Manual) Brand Name: RadioMaster Item Name: T8 Lite V2 Transmitter Model: T8 Lite V2 Mode: Mode1/Mode2 Size: 160*130*45mm Weight: 218g Frequency: 2.400GHZ-2.480GHZ RF Module: CC2500 Protocol Options: D8/D16 V1 Transmission power: 20dbm Antenna gain: 2db Range: > 1km @ 20dbm (depending on the receiver) Battery: Built in 3.7v 1000mah Lithium battery Charging: Built in USB-C charging Firmware: Independent development system Channels: Up to 8 channels (depending on the model / receiver) Gimbal: High-precision quad bearing potentiometer sensor gimbal *Does not support OpenTX Bind mode for D8 protocol receivers: 1. Turn on the transmitter and keep the throttle at its lowest position. Press and hold the bind button for longer than 1 second, the transmitter will start beeping in a beep-beep-beep pattern, signaling D8 mode. If the transmitter beeps in a beep(x2)-beep(x2)-beep(x2) pattern, this means the transmitter is in D16 mode and the bind button should be pressed momentarily to return to D8 mode. 2. Power on the receiver, press the bind button on the receiver within 3 seconds to enter bind mode on the receiver. 3. The red light on the receiver will flash, signaling that the unit has bound successfully. Turn the receiver off and on again for the unit to function correctly. Bind mode for D16 protocol receivers: 1. Turn on the transmitter and keep the throttle at its lowest position. Press and hold the bind button for longer than 1 second, the transmitter will start beeping in a beep(x2)-beep(x2)-beep(x2) pattern, signaling D16 mode. If the transmitter beeps in a beep-beep-beep pattern, this means the transmitter is in D8 mode and the bind button should be pressed momentarily to return to D16 mode. 2. Power on the receiver, press the bind button on the receiver within 3 seconds to enter bind mode on the receiver. 3. The red light on the receiver will flash, signaling that the unit has bound successfully. Turn the receiver off and on again for the unit to function correctly. Note: - D8 receivers made by different manufacturers may have different binding procedures. Refer to the user manual for precise binding instructions. - D16 receivers made by different manufacturers may have different binding procedures. Refer to the user manual for precise binding instructions. Package Included: (Optional Mode)

Sản Phẩm Tương Tự

Sản Phẩm Liên Quan

*Sản phẩm được thu thập tự động để tiếp thị. Chúng tôi không bán hàng.